News
Call us on
+86-571-61712588
If you have any questions, please contact us
GO >>
Home > News > Content

Build your own Liquid Nitrogen Generator

I have always been intrigued by science demonstrations using liquid nitrogen, and often made trips to a local welding supply store with my stainless steel vacuum flask to purchase liquid nitrogen and satisfy my cryogenic craving at home. After a few fill-ups, I wondered about the possibility of making liquid nitrogen on demand. Some companies have already produced self-contained liquid nitrogen generators that are designed for small laboratories. The Elan2 would be ideal for home experimenters, but the cost is over $10,000, so I decided to build a similar device with less total output, lower purity, and at much lower cost. The device that I built cost less than $500 and produces l liter of liquid nitrogen per day.

Nearly all large-scale liquid nitrogen is made by compressing, cooling, and expanding air. This process removes heat from the air and can be repeated until the air liquefies. The condensing gasses are then separated using fractional distillation. This process cannot be easily scaled down because it relies on maintaining a complex, large distillation column to separate nitrogen from the other gasses in air. To avoid using a distillation column, one could use a nitrogen separation device to strip out the nitrogen from air at room temperature. Then, the room temperature nitrogen can be liquefied via the standard compression and expansion method. This is likely the process used in the Elan2 generator. However, it still requires the use of a very high pressure compressor and heat exchanger, extensive insulation and many other custom parts.

Nitrogen Storage Tank

I purchased the Superfilter on eBay and extracted the cryocooler. In order to test the device, I attached a small heatsink to the cooler’s cold tip, placed the tip into a household vacuum flask, and powered up the unit. After 30 minutes, I took the cryocooler out of the flask, and noticed a small amount of liquid air had collected at the bottom. Inspired by this success, I continued construction of a more complete liquid nitrogen generator. I already owned a 30-liter dewar (large vacuum flask) and fabricated an acrylic plate that would seal the top of the dewar while the cryocooler was also mounted to the plate with its heatsink hanging down into the neck of the flask. I also removed the cryocooler’s finned heatsink on its heat rejection area and replaced it with a liquid- cooling manifold. Liquid cooling lowered the heat rejection area temperature more effectively than forced air cooling, and this ultimately lead to higher system efficiency.

The Stirling-cycle cryocooler with custom heatsink and acrylic dewar-mounting plate. The mounting plate has a rubber gasket that forms a seal with the neck of the dewar.

The liquid nitrogen generator has two basic sections, the dewar with cryocooler, and the air processing equipment that creates dry nitrogen from atmospheric air. The dry nitrogen is fed into the dewar at just above atmospheric pressure where the cryocooler chills the nitrogen until it liquefies and drips off the heatsink. Surprisingly, most of project’s time budget was spent designing and building the equipment to produce dry nitrogen from air. There are some companies who make dry nitrogen supply devices, but even small units are meant for much higher throughput than what is needed by this liquid nitrogen generator. Each liter of liquid nitrogen requires about 700 liters of room temperature nitrogen gas. 700 liters per day is only 0.5 l/min, a very modest flow rate. One popular, but unnecessary use for relatively low-purity nitrogen is filling car tires. I tried to purchase such a machine, but the cost and flow rate were much higher than anticipated. Instead, I found a very small nitrogen separation membrane on eBay. It’s original use was unknown. The separation membrane is the actual component inside commercial nitrogen generators that perform gas separation. The membrane is formed into a large bundle of hundreds of 2mm dia tubes. Air is fed under high pressure into one end of the bundle. The tube walls are semi-permeable and allow oxygen, water vapor, carbon dioxide and other “fast” gasses to permeate relatively quickly. Nitrogen and heavier gasses do not permeate as quickly, so the concentration of nitrogen is much higher at the exit end of the tubes than it is at the input end. Higher purities of nitrogen can be achieved by restricting the flow rate through the tubes, thus allowing plenty of time for the unwanted gasses to permeate the tube walls and leave the system. The resulting nitrogen will contain trace amounts of argon and even smaller amounts of other noble gasses.

Air Processing Unit

Air processing unit with two aluminum desiccator chambers, two small black coalescing filters, two beige carbon filters, nitrogen separation membrane at lower right, and a flow meter with needle valve.

I also built a dessicator from aluminum cylinders filled with silica gel and plumbed this into to the system before the air reaches the separation membrane. These units are available commercially, and the one that I built is not particularly specialized. Separation membranes also exist for removing water, and this would be an improvement over silica gel dessicators, which require the gel to be dehydrated in an oven after it becomes saturated with water.

The liquid nitrogen generator has proved to be a reliable, but fairly slow method to produce small quantities of liquid nitrogen at home. The initial cool-down of the dewar takes about 12-18 hours, after which liquid nitrogen is produced at a net rate of 1 liter per day. The generator uses about 300 to 400 watts of electricity (includes the water chiller, which cycles on and off), so the energy cost for producing one liter of liquid nitrogen is about 8.5 KWh, or $1.10. This is substantially less expensive than having a thermos filled at a local welding supply store.

LN2 Generator overview

System overview showing a window air conditioner converted into a liquid cooler with liquid cooling lines running to the cryo- cooler which is mounted atop a Linde dewar. The additional refrigeration compressor mounted on top of the air conditioner unit compresses atmospheric air for liquid nitrogen production.


Product Categories
To learn more, please click into each category ...
Copy Right Reserved YDGET